Apply a layer of the compound to the joint or area below the removed tape. Be sure this layer is a bit wider than the width of the tape. Next, tear a piece of drywall tape to fit the required length. Center the tape over the area and then place it on the drywall compound. Once that is done, hold the top edge of the tape and pull the drywall knife down the tape. Press evenly, making sure to embed the tape into the compound, removing any air bubbles.
Let this dry before going to the next step. The last thing to do once dried is to dip the long edge of an 8-inch drywall trowel in the compound. Apply a one-sixteenth inch layer of compound over the strip of drywall tape. Allow this to dry and then repeat one more time.
Sand the area after the drywall compound is completely dry. You will want to create a smooth surface for painting. Drywall mud compound is used pretty much for any drywall repair job. For the most part, it is simple and effective to work with because of its easy application. However, there is a problem that does persist when it comes to drywall mud which is bubbles.
You get bubbles in drywall mud because it is a porous compound. This means that air is able to pass through it.
In instances where the drywall cant absorb the air from the mud into the sheetrock, the air will be displaced through the mud—other examples of bubbles occur with drywall mud and tape due to varying temperatures and inadequate adhesion.
For the best drywall mud, click here. This article will briefly discuss what drywall mud compound is, and with that, we will take a look at the different kinds of bubbles that occur in drywall mud and why they occur. Then we will take a look at a detailed solution to solve the drywall bubble problem that plagues a lot of maintenance specialists. In order to get a better understanding of why drywall mud acquires bubbles when the mud is applied to drywall, it will first be beneficial for us to understand what drywall mud is.
Then we can understand why this phenomenon occurs. Drywall mud is actually a type of joint compound used to strengthen and smooth over drywall and joints. There are two types; one comes in a powder form dry that you will mix yourself, and the other is pre-mixed mud.
The latter will be bought ready-to-go, and you can start applying it instantly. There are various types of drywall mud that have different cure times a set amount of time required for it to dry and come with multiple fire ratings. It s important to note that the fire rating for these products is tested as a system component as a whole and not as individual elements.
No matter which drywall compound mud you use, there is always a chance that it will bubble, and this is because the mud is mixed with water, and due to this, it is very porous in its nature has gaps so air or water can seep through. There will be two main reasons you get bubbles in your drywall mud and the first reason is due to paint on the drywall, and then the other reason is due to the drywall tape. We initially said that drywall mud is porous and, additionally, so is drywall sheetrock itself.
This means that it has tiny spaces that allow it to absorb air and water. Hence when drywall compound is spread over it, those little gaps holes in the sheetrock suck in the air of the drywall mud. This is why you constantly find that there will typically be no bubbles if you apply mud to clean drywall, which is excellent. The problem comes in and persists when the drywall is painted. It is even more of a hassle depending on the paint and what type of finish it has paint with a high gloss finish will typically cause the most problems.
Due to the paint covering the drywall, the sheetrock loses its permeability it is not porous anymore. You have to remember that most paints are designed to be water-resistant and repel water. Imagine if the paint were not this way, then your house would need to have its inner wood beams replaced on a regular basis. Due to the drywall not being able to soak up the mud now because of the paint, the air still needs to escape somewhere as the mud cures.
The only other direction the air can now travel is in the opposite direction of the paint, which is why bubbles occur. There are two types of drywall mud: premixed and dry. Premixed comes ready to use, whereas dry compound requires the user to add water and adjust the thickness and consistency. For the sake of simplicity and convenience, premixed drywall mud is a very popular choice, but it often comes a little too thick.
If you find that your premixed joint compound is too thick and not spreading nicely, do not hesitate to add some water to it and thin it out a bit.
Generally speaking, you should use drywall mud relatively soon after purchasing it. Storing drywall mud for extended periods may cause it to harden, soften, lose its adherence, and alter its viscosity. Old drywall mud may no longer possess the integrity it once had, and using it can result in a range of different problems, including air bubbles. Do not use old and compromised drywall mud.
Make sure it is new, or like new, before using. While you usually apply mud to new and unpainted drywall, there are situations where you need to use joint compound for patching over holes or cracks in painted drywall. Applying mud to painted walls greatly increases the chance that you will encounter bubbling. Unlike unpainted drywall, which is papery and porous, painted drywall is sealed and cannot absorb the compound and the air bubbles therein.
Therefore, all of the air in your mud is pushed outward and appears on the surface. Another frequent cause of drywall mud bubbling, specifically under the tape, is that beginners press too much mud out from under their tape with their knife, which does not only cause the mud to bubble but will also leave your tape with a poor and unreliable adhesion that is bound to lift and separate sooner or later.
While it is right to smooth your tape down and press out the excess mud, you need to leave enough so that it can absorb the air bubbles and form a strong seal. Drywall taping is a fairly straightforward process, but many things can go wrong, which is why it is important to be consistent and learn from every problem that you encounter. For an easy-to-follow, six-step guide on how to properly apply drywall tape so that you may get it right the first time, see this article by Home Depot.
After a few hours the cracks in the mud also dry out. The water will eventually evaporate from the fissures and by the time of the next paint job they will be ready to produce blisters all over again. Uneven drying — uneven drying, or a lack of 'curing' time for your plaster or stucco wall can also contribute to nasty air bubbles.
The trapped moisture inside will cause the paint to blister due to the presence of water that attempts to come out as the plaster and paint as they both drying. Apply three or more coats of very thin compound rather than one or two heavier coats.
Yes, it takes time for the compound to dry, but don't try to rush the drywall taping process along by applying fewer, thicker coats.
What causes drywall tape to wrinkle? Most common causes Probably the most common cause is that there was insufficient drywall compound applied to the taped joint or improper application. Moisture or dampness may also cause the tape to come loose. Why does drywall tape blister? The most common reason for drywall tape blisters is a lack of joint compound between the tape and the drywall surface. All too often I see rookie weekend warriors make the mistake of removing too much joint compound from underneath the tape.
Some people press the taping knife so hard they snap it in two!
0コメント